Chemica HotMark Heat Transfer Vinyl - 14.75 in x 11 ft - Red

ET-HOT-1511-406

5 out of 55 out of 55 out of 55 out of 55 out of 5 () | Write a Review

Shipping Weight: 0.85 lbs.

Chemica HotMark Heat Transfer Vinyl - 14.75 in x 11 ft - Red
×You will have to log in to add this item to your wish list.
Processing...

$28.95


Product Details: Chemica HotMark Heat Transfer Vinyl - 14.75 in x 11 ft - Red

Overview

Chemica US HotMARK 70

  • Matte finish for cotton, polyester, acrylic fabrics
  • Very thin, soft, and super stretchable
  • 2.2 - 2.4 mil
  • High speed cutting, ultra-fine detail, easy weeding
  • 50 Colors
    Application Directions:
    Reverse cut through adhesive layer to plastic backing. Cut with a 45 degree blade. Weed excess material. Lay cut pattern on fabric. Cover design area with teflon sheet. Heat transfer at 300 degrees F to 340 degrees F for 20 seconds with high pressure. Peel cold. Transferred image can be covered with Teflon sheet and reheated, if necessary.
    Wash Instructions:
    Do NOT exceed water temperatures of 180 degrees F. Can be dry-cleaned. Do NOT dry in a tumble dryer.
  • Customer Reviews
    Average Customer Review: 5 out of 55 out of 55 out of 55 out of 55 out of 5 4.62 out of 5 (8 Reviews)

    Click here to write an review and share your thoughts with others.


    5 out of 55 out of 55 out of 55 out of 55 out of 5 HOTMARK 70 is #1

    This is my number one choice in Heat transfer vinyl. I put my press on 335 for 20 sec with high pressure the first time, then I pull plastic backing cover off. Then apply teflon sheet and press again for 10 seconds at a high pressure. I still have shirts that I pressed 4 years ago that still look as good. Vinyl looks better than the shirt after years...Highly recommend
    zayzcustomdecalandsigns (CUMBERLAND, KY) 9/24/2013


    4 out of 54 out of 54 out of 54 out of 54 out of 5 This material is good.

    I've tried a couple other materials but I really like this one.. One thing that I dislike about this material is that it is not red on both sides. The only problem that I've had with this, is when cutting really small designs or designs that end with a fine point; if the vinyl were to fold on the tip or if you have small flakes left over after weeding your splatter effect design, you normally see a little bit of white. If it were red on both sides, this would not be an issue. Because of that I tried SISER Easy Weed which is red on both sides of the vinyl and worked great.. just didn't like the fact that the backing paper was so sticky and made stacking of the cut material annoying so I came back to the EnduraTex... placing my order now as a matter of fact. This is of course my own opinion, just thought I'd share my experience.
    Andre (Kettering, OH) 3/31/2012


    3 out of 53 out of 53 out of 53 out of 53 out of 5 Hard to Find Right Settings?

    I am having trouble pressing. Using 300F @ 20 seconds w/ teflon sheet. Top half seems like it doesnt want to stick, repressed looks a bit wrinklish. Am i doing something wrong with this or what?

    EDITOR: Hello Fidel! Try increasing the pressure on your heat press. HotMark requires more pressure for the adhesive to set. Please click here for more information about this.
    FIDEL MARTINEZ (SAN PABLO, CA) 10/22/2011


    5 out of 55 out of 55 out of 55 out of 55 out of 5 Hotmak 70 is worth the money!!!

    Hotmark 70 is AWESOME DURABLE and I've been ordering it since. Grandparents love to show support for their grand-kids in sports. Other parents keep me busy with additional orders after they see the shirt I made. Thanks, Ruby for making it happen. Ordering is fast & easy.
    Wally V. (Pasadena, TX) 3/31/2010


    5 out of 55 out of 55 out of 55 out of 55 out of 5 Best I Have Tried!

    This EnduraTex HotMark 70 is the best product I've tried in this category, it does cut/weed easily. Also have not had any complaints from customers of letters falling off the garment.
    Tammy Waites (Salem, AL) 1/27/2010